October 13, 2024
How to Install a Power Outlet: A Comprehensive Guide

There can be various opinions regarding how easy or hard it is to install a power outlet. However, installing one is much more than just a simple device and should be performed with great care and precaution. Ignoring the specific procedures outlined in this guide will lead to problems later during installation. 

The power outlet installation instructions in this specific guide focus on IGOTO Electric’s DS Series outlets, which are favored by many professional electricians and contractors. If you are going to change an old power socket or set up a new one, make sure you know how to do it properly so it is safe to use and works as intended. We understand the importance of risks and take you through all safety guidelines as well as provide advanced methods of executing the procedures for a power installation.

Important Safety Notice

Important Safety Notice

You must be prepared for a couple of points about safety points if you decide on performing any electrical installations:

  • Do not forget that all work with electricity must only be done by licensed power professionals.
  • Installation is to be completed under local, state, or country standardization.
  • It is important to note that suitable methods and equipment related to safety are to be applied.
  • It is obligatory to completely switch off the power supply before running any kind of work.

Understanding Power Outlets

Types of Power Outlets

The evolution of technology has led to the development of different power outlets:

  1. Standard Power Points

These are household plug points that are used widely

Available in one or two-socket options

Includes protective safety shutters

  1. Weatherproof Outlets

This type is meant to be placed outside

Resistant to water and other elements

Designed to withstand harsh outdoor conditions

  1. Specialized Outlets

IGOTO Electric’s DS Series includes:

High-safety features

High-quality materials

Compliance with Australian standards

Professional quality

Essential Components

The installation of a power outlet includes the following important elements and features:

  • Outlet box
  • Wiring (active, neutral, and ground)
  • Mounting hardware
  • Cover plate
  • Safety features (such as shutters and grounding)

Pre-Installation Requirements

Required tools and materials:

  1. Voltage tester
  2. Screwdrivers
  3. Wire strippers
  4. Cable ripper
  5. Wire connectors
  6. Needle-nose pliers
  7. IGOTO Electric DS Series outlet
  8. Proper mounting screws
  9. Safety equipment (gloves, safety glasses)

Safety Preparations:

Power is physically cut off physically

Verify the circuit is dead using a voltage tester

Properly equip yourself with personal protective equipment

Do not leave the working area dirty or dark

Have all tools readily available

Step-by-Step Installation Process

Preparing for Installation

This is critical as before you start with the installation of the power unit, ensure that you have the DS Series IGOTO Electric power unit with you. Now, perform these initial steps:

Location Selection

  1. Locate the wall site at an appropriate place
  2. Identify if any wires or other obstructions are there
  3. Ensure compliance with local electrical codes
  4. Identify if any wires or other obstructions are there

Power Disconnection

  1. Identify if any wires or other obstructions are there
  2. Find the correct circuit breaker that should be switched off
  3. Check using a voltage tester that the power is off
  4. Check all precautions again

Installation Steps

For Replacing Existing Outlets:

Remove Old Outlet

Take away the faceplate by unscrewing it carefully

Pull out the existing power outlet from the fixture

Take a picture of how the wiring is connected presently

Label wires if necessary

Wire Connection

Connect the active (brown/red) wire to the brass terminal

Attach neutral (blue/black) wire to silver terminal

Secure the ground (green/yellow) wire to the ground terminal

All connections must be tight.

For New Outlet Installation:

Wall Preparation

Mark the outlet location

Outline a hole that is suitable for the box’s size

Place the mounting box firmly

Check that the depth and alignment is correct

Cable Installation

Route suitable power cabling to the area

Leave enough wire length for connections

Secure cables properly within the wall cavity

Ensure compliance with local wiring regulations

Quality Assurance

After the installation is done, the following checks are necessary:

  1. Physical Inspection

Check if all the screws have been perfectly secured.

Check if outlet is flush with the wall

Check that the cover plate has a frame that fits properly.

Make sure the outlet is not wobbling around.

  1. Electrical Testing
Electrical Testing

Switch the power back on at the circuit breaker.

Use a voltage tester to test the outlet.

Test if the outlet has been grounded properly.

Make sure the outlet is connected to its positive and negative sides.

Professional Recommendations

Expert Installation Tips

Use the IGOTO Electric outlet as follows:

  • Use manufacturer-recommended tools
  • Follow all the guidelines and steps for installation.
  • Maintain proper clearances
  • Take pictures of all the connections.

Frequently Asked Questions

How long does outlet installation take?

The installer should expect to take around 20–30 minutes to install one outlet, and it will take longer depending on the number of outlets being installed and the amount of prepping done beforehand.

What is the lifespan of a power outlet?

The DS Series from IGOTO Electric has been built for a life span of around 15 to 20 years, depending on how well it is maintained.

Are special tools required?

Although some basic electrical tools may be needed, IGOTO Electric supplies all necessary mounting hardware.

Conclusion

This is a very sensitive and delicate power inlet socket outlet installation that should be done with utmost professionalism. This document furnishes readers with the necessary details regarding the installation process, but it is important to reiterate that electrical installation works are only to be undertaken by authorized technicians aware of the local regulations and safety practices.

The DS Series of power outlets from IGOTO Electric also rank among the best in the market and come with ancillary aspects that make them safe and last longer. Whether it is the replacement of outlets in the electrical wiring of a property or the put-up of new outlets, the right type of product and its professional placement should be obtained for personal safety and assurance. Have you decided to change the electrical sockets? If yes, then find various IGOTO Electric products and a certified installer near your location from their official website.

Article Source
IGOTO Electric uses only high-quality sources, including peer-reviewed studies, to support the facts within our articles. Our commitment to accuracy and reliability ensures that readers receive well-researched information they can trust.
GET A CONTACT
SEND US A MESSAGE​
GET A CONTACT
Send Us a Message
YOUR NAME
COUNTRY
COMPANY
YOUR EMAIL
YOUR PHONE
YOUR MESSAGE
en_USEnglish