

Five mechanisms stacked on an 80 mm face. Where a horizontal five gang would need 121 mm of clear wall, this needs 80 mm and uses the height instead.
Five is where stacking starts to test reach. The bottom gang sits low enough that a tall adult bends slightly and a shorter user bends noticeably, so the least-used circuit belongs there.
The typical job is a service wall or riser where several circuits terminate in a narrow slot beside a duct or a door. Those walls are tall and thin, which is exactly the vertical plate.
The plate is 80 mm wide, so plan on 90 mm clear. Below that it will not seat without fouling a trim or a corner, and a plate jammed against an architrave never sits flat.
Height is the other number. Five gangs need 121 mm of plate plus clearance above and below, and the bottom gang lands where a shorter user may not reach.
| Parameter | Details |
|---|---|
| Product | Australian standard 5 gang wall switch, vertical brushed aluminium plate |
| Switching Function | 2 way (SPDT) per gang; individual gangs available as 1 way, intermediate or double pole |
| Rated Current | 10A per gang; 16A on selected gangs |
| Rated Voltage | AC250V |
| Number of Gangs | 5 gang |
| Terminals | Screw terminals, back and side cable entry |
| Contact Material | AgNi15/Cu silver alloy contacts on T2 copper conductor |
| Panel Material | Brushed aluminium plate, 80 × 121 mm |
| Surface Finish | Hairline brushed; anodised colour layer |
| Available Colours | Silver white, matte black, silver grey from stock; custom RAL on request |
| Mounting | Standard Australian wall box, horizontal or vertical |
| Mechanical Endurance | ≥ 40,000 operations per gang |
| Protection Degree | IP20, indoor use |
| Standard | AS/NZS 3112 |
| Approval | SAA |
| Warranty | 15 years (IGOTO standard warranty) |
| Model | Configuration |
|---|---|
| CS309-V | 5 gang, 1 way, 10A, vertical |
| CS310-V | 5 gang, 2 way, 10A, vertical |
| CS310-VDP | 5 gang, double pole, 10A, vertical |
| CS310-V/005 | 5 gang, intermediate, 10A, vertical |
Five gang plates are built to order. The bottom gang is the one most affected by reach, so confirm which circuit sits there before production.
The horizontal five gang, for walls with 121 mm clear, is CS310. The remaining plate sizes are on the CS series page.

Five circuits converging on one position is already a compromise. Doing it on an 80 mm wall means the compromise has to be managed in the vertical dimension as well, and the thing that gives is reach.
The CS310-V stacks five two way mechanisms at 10A on an 80 mm by 121 mm brushed aluminium face. Any position can be intermediate or double pole, and the terminals take back and side cable entry.
If the wall has 121 mm, take the horizontal five gang: it is easier to read and puts every gang at a similar height. This plate is the answer for the wall that does not, and the honest cost is that the bottom gang sits low.
Stacking four is comfortable. Stacking five starts to fail the reach test at the bottom. An adult of average height reaches the lowest gang with a slight bend; a shorter user or a wheelchair user may not reach it at all.
That is not a reason to refuse the product, it is a reason to assign the bottom gang to the circuit nobody needs to reach in a hurry, a store room, a rarely used exhaust fan, a spare.
Five mechanisms on 121 mm is the densest vertical configuration we build, so the plate is assembled on a jig and checked against a straight edge for bow before packing. Each gang is tested independently, then the plate as a unit.
Vertical plates are brushed along the long axis and inspected for colour before assembly. OEM orders can be laser marked and packed to your specification, with mixed orientations in one consignment.
The usual application is a service wall beside a duct, a riser cupboard, or a plant room door, where the clear section is tall and narrow and several circuits terminate.
Those are also positions where the finish matters less than the function, which is why the vertical plate is often specified in a plain finish.
In that setting the metal face is a durability choice rather than a design one. Anodised aluminium does not yellow, does not craze and wipes clean, which is why it survives a plant room better than a moulded plate.
Five stacked is a reach decision as much as a product decision. Confirm who has to reach the bottom gang.
Custom anodised colours, laser marking and retail packaging on the vertical five gang platform, with SAA documents for the certified range.
Factory-direct pricing for project quantities, with scheduled delivery and mixed orientations in one consignment.
Account management, Australian datasheets and priority production for partners supplying service and utility areas.
Send the wall width, the floor-to-plate height and the circuit order, and we confirm whether five stacked is workable or the circuits should split. Factory-direct pricing is quoted per order; SAA documentation ships with the consignment.
Contact Our Sales TeamSix is available as well, but five stacked is where reach becomes the limiting factor rather than the plate. If every circuit has to be reachable, five on one plate is already too many and the answer is two plates rather than a larger one.
Assign the least-used circuit to it, or split the plate. Accessibility guidance usually refers to switch heights rather than plate sizes, so the fix is to move the circuit rather than to change the product. Confirm the requirement with your electrician or access consultant.
It uses the standard Australian box format for the plate, with mechanisms stacked rather than spread. Depth is the same as a horizontal five gang; the practical requirement is that the box is level and flush, because a 121 mm face shows a taper.
|
High-Quality Material
|
The CS310-V/CS309-V features a high-quality acrylic panel that provides both elegance and fire resistance. The switch contacts are made of silver alloy (AgCd015/Cu), offering superior conductivity and longer lifespan.
|
|
Long Life Cycle
|
Designed for durability, the CS310-V/CS309-V switch can withstand over 40,000 on-off operations, making it perfect for high-use environments such as offices, schools, and shopping centers.
|
|
Enhanced Conductivity
|
The T3 copper terminals and phosphor copper contacts ensure excellent electrical conductivity and strong elasticity, contributing to a reliable and consistent performance over time.
|
|
Versatile Design
|
The sleek, modern design of the CS310-V/CS309-V switch makes it a versatile choice for various applications, including residential, commercial, and industrial installations.
|
|
High Safety Standards
|
With SAA certification and compliance with ISO9001 and ISO14001, the CS310-V/CS309-V guarantees top-notch quality and safety. It meets all Australian safety standards, ensuring peace of mind for end-users.
|
IGOTO – A Trusted Manufacturer of High-Quality Electrical Products
Founded in 1999, Zhejiang IGOTO Electric Co., Ltd. has become a leading manufacturer and supplier of electrical products, specializing in switches, sockets, and related components. With over 20 years of experience in the industry, IGOTO Electric has established itself as a trusted partner for B2B clients worldwide, including well-known companies in Australia, South America, and Southeast Asia.
Our commitment to quality and innovation is backed by over 15 years of research and development, with a focus on producing electrical products that meet the highest safety and performance standards. As an OEM partner for several large global brands, we pride ourselves on delivering solutions that meet the unique needs of each customer.
Our Core Values:

We are dedicated to becoming your reliable partner in providing safe, durable, and cost-effective electrical solutions.
